網站首頁 關于我們 產品展示 新聞中心 應用案例 銷售網絡 在線留言 聯系我們
產品分類
 進口電磁閥
 進口蝶閥
 進口球閥
 進口疏水閥
 進口調節閥
 進口截止閥
 進口減壓閥
 進口閘閥
 進口流量計
 進口止回閥
 進口真空閥
 進口低溫球閥
 進口低溫截止閥
 進口低溫安全閥
 進口低溫過濾器
 進口磁力泵
 進口隔膜泵
 進口離心泵
 進口化工泵
 進口計量泵
 進口消防泵
 進口真空泵
 進口轉子泵
 產品搜索
 業務聯系
 人才招聘
 客服電話
 在線聯系
   首頁 - 產品展廳 - 產品介紹  
  產品名稱: 進口臥式單級單吸清水離心泵
  產品型號:
 
 
  咨詢電話:0752-5588737 黃東
 相關產品
 進口低轉速立式離心泵
 進口臥式單級單吸清水離心泵
 進口水力噴射器
 進口單級單吸全不銹鋼耐腐蝕離心泵
 

產品概述Product description

進口臥式單級單吸清水離心泵,是全國聯合設計的節能泵,它是其他單級清水離心泵的更新型。優點有:全系列水力性能布局合理,用戶選擇范圍寬,檢修方便;效率和吸程達到國際平均先進水平。本型泵適用于工業和城市給水、排水,也可用于農業排灌及供輸送清水或物理化學性質類似于清水的其他液體之用,溫度不高80℃。

Imported horizontal single-stage single-suction centrifugal pump water, is the joint design of energy-saving pump, which is the other single-stage centrifugal pump water newer. Advantages are: a full range of hydraulic performance and reasonable layout, the user selects the range, easy maintenance; efficiency and suction lift up to international advanced level average. This pump is suitable for industrial and urban water supply, drainage, irrigation and agriculture can also be used for conveying water or physical and chemical properties similar to water or other liquids, the temperature is not high 80 ℃.


產品特點Features


1、進口臥式單級單吸清水離心泵根據國際標準ISO2858所規定的性能和尺寸設計的,主要由泵體、泵蓋、葉輪、軸、密封環、軸套及懸架軸承不見等組成。
2、進口臥式單級單吸清水離心泵的泵體和泵蓋部分,是從葉輪背面處剖分的,即通常所說的后開門結構形式。其優點是檢修方便,檢修時不動泵體,吸入管路,排出管路和電動機,只需拆下加長聯軸器的中間聯接件,即可退出轉子部分進行檢修。
3、泵的殼體(即泵體和泵蓋)構成泵的工作室。葉輪、軸和滾動軸承等為泵的轉子。懸架軸承部件支撐著泵的轉子部分,滾動軸承受泵的徑向力和軸向力。
4、為了平衡泵的軸向力,大多數泵的葉輪前、后均設有密封環,并在葉輪后蓋板上設有平衡孔,由于有些泵軸向力不大,葉輪背面未設密封環和平衡孔。
5、泵的軸向密封環是由填料壓蓋,填料環和填料等組成,以防止進氣或大量漏水。泵的葉輪如有平衡,則裝有軟填料的空腔與葉輪吸入口相通,如葉輪入口處液體處于真空狀態,則很容易沿著軸套表面進氣,故在填料腔內裝有填料環通過泵蓋上的小孔,將泵室內壓力水引至填料環進行密封。泵的葉輪如沒有平衡孔,由于葉輪背面液體壓力大于大氣壓,因而不存在漏氣問題,故可不裝填料環。
6、為避免軸磨損,在軸通過填料腔的部位裝有軸套保護。軸套與軸之間準有O型密封圈,以防止沿著配合表面進氣或漏水。
7、泵的傳動方式是通過加長彈性聯軸器與電動機聯接的,泵的旋轉方向,從驅動端看,為順時針方向旋轉。


1, imports of horizontal single-stage single-suction centrifugal pump water based on performance and size ISO2858 international standard provisions designed mainly covered by the pump, pump, impeller, shaft seal rings, bushings, bearings and suspension but not other components.
2, imports of horizontal single-stage single-suction centrifugal pump water pump body and pump cover part of the back office split from the impeller, that is commonly referred to as post-formal-door structure. The advantage is easy maintenance, repair does not move when the pump, suction line, discharge line and the motor, just remove the spacer coupling intermediate coupling member, you can exit the rotor parts for maintenance.
3, the pump housing (ie, pump and pump cover) constitute the pump studio. Impeller, shaft and rolling bearings as the pump rotor. Suspension bearing member supporting the rotor portion of the pump, the rolling bearing by radial and axial forces of the pump.
4, in order to balance the axial force of the pump, the impeller of the pump before the most, after the sealing ring has, in the rear cover plate is provided with an impeller balance holes, due to force some small shaft, the impeller is not provided on the back of the seal rings and balance holes.
5, pump axial seal ring is composed of packing gland, packing ring and filler and other components to prevent water leakage into the air or a lot. If the pump impeller balance is equipped with wadding impeller inlet in communication with the cavity, impeller inlet of liquid in a vacuum, it is very easy along the surface of the intake sleeve, so the packing chamber equipped with packing rings by hole pump cover, the pump chamber pressure of water lead to the packing ring seal. If no pump impeller balance holes, due to the back of the impeller fluid pressure greater than atmospheric pressure, so there is no leakage problems, it is time to install packing rings.
6, to avoid shaft wear in the shaft through the packing chamber parts fitted sleeve protection. Associate O-ring between the sleeve and the shaft to prevent along the mating surface of the intake or leaking.
7, the pump drive is through lengthened flexible coupling and motor coupling, rotation direction of the pump from the drive end, clockwise rotation.


 

友情連接: 百度 | 儀器供應商 | Equipment Series | 離合器 | 億商網 | 中國商業港 |
Copyright 2005 hitachifm.com All Rights Reserved. 惠州費希爾閥門有限公司 版權所有
地址:廣東省惠州市大亞灣區石化大道中438號新華聯廣場10棟 電話:0752-5588737 粵ICP備19021819號
日韩欧美一中文字蒂幕二区,亚洲AV网址在线观看|四虎在线观看国产入口|中文欲色影视